Note: since the slide rail is coated with antirust oil, please wash it with cleaning oil before installation. It is recommended to use the lubricating oil with low viscosity to remove rust on the main shaft.

2. 將滑軌輕輕地裝在床身上后,輕輕地鎖緊裝配螺箖,使潸軌與安裝面輕輕地靠緊。(床身的基準面要與滑軌有標記線的一側相接觸

2. After gently installing the slide rail on the bed, gently lock the assembly screw sheath to make the slide rail slightly close to the installation surface. (the datum plane of the bed shall be in contact with the side of the slide rail with the marking line

注意:安裝使用之螺絲需先洗凈,并確認規格與滑軌相符,才可鎖緊螺絲。

Note: the screws used for installation shall be cleaned first and the specification shall be consistent with the slide rail before locking the screws.

3. 按順序?qū)⒒壍亩ㄎ宦萁z鎖緊,使滑軌與轉向安裝面緊密相接。

3. Lock the set screws of the slide rail in sequence to make the slide rail closely connected with the steering mounting surface.

4.使用扭矩扳手,將裝配螺絲按規定的扭矩鎖緊,使其緊密相接。

4. Use a torque wrench to lock the assembly screws according to the specified torque to make them closely connected.

注意:滑軌裝配螺絲的鎖緊順序是,從中位置開始向端部按照順序鎖緊,這樣也可獲得穩定。

Note: the locking sequence of slide rail assembly screws is to lock them from the middle position to the end in order, so as to obtain stability.

5.其馀的滑軌也依同樣的方法安裝值到全部完成。

5. Other slide rails are installed in the same way until all are completed.

6.將專用防麈蓋一點一點地敲入裝配螺絲孔,到與滑軌的上面同一平面為止。

6. Knock the special anti dust cover into the assembly screw hole bit by bit until it is on the same plane as the upper surface of the slide rail.

滑塊的安裝

Installation of sliding block

1.將工作臺慢慢地裝在滑塊上,螺絲非正式鎖緊

1. Slowly install the workbench on the sliding block and lock the screws informally

2.通過定位螺將滑塊的基準側與工作臺側面基準面接觸上,使工作臺定位

2. Contact the reference side of the slider with the reference plane of the side of the worktable through the positioning screw to position the worktable

3.正式鎖緊基凖側和被動側的裝配螺絲安裝完成。

3. Formally lock the assembly screws on the standard side and the passive side, and the installation is completed.

注意:按對角線所標示之順序?qū)⒀b配的螺絲鎖緊，進行使工作臺更加均衡的固定。

Note: lock the assembled screws in the order indicated by the diagonal to fix the workbench more evenly.

此方法對于找出滑軌的直線度并不費時,且不需要加工用于固定的定位銷;因此,可大幅度縮短安裝時間.

This method is not time-consuming to find out the straightness of the slide rail, and there is no need to process the positioning pin for fixing; Therefore, the installation time can be greatly shortened

上一篇：直線導軌滑塊的日常維護包含哪幾方面？
下一篇：直線導軌和直線滑軌的區別體現再哪里？

相關：

306135.com-北条麻妃99精品青青久久,一区二区精品国产,久久久久免费网,99久久精品费精品国产一区二区

直線導軌的安裝需要注意些什么？