新聞中心
左右旋滾珠絲桿如何確認“行程”
來源:http://www.306135.com/ 日期:2019-07-03 發布人:
左右旋滾珠絲桿如何確認“行程”,濟南共潤科技有限責任公司講解下滾珠絲桿每段行程的計算方式:
How to confirm the "stroke" of the left and right ball screw? Jinan Gongrun Technology Co., Ltd. explains the calculation method of each stroke of the lower ball screw:
滾珠絲桿的行程有一個公式的,里面包含3個因素。
Ball screw stroke has a formula, which contains three factors.
1、絲桿螺紋長,2、有效行程, 3、余量長度。
1. Screw thread length, 2. Effective stroke, 3. Allowance length.
絲桿螺紋長=有效行程+螺母長+螺紋兩頭距離。
Thread length of screw = effective stroke + nut length + safe distance at both ends of thread.
總長=絲桿螺紋長+軸頭加工長度
Total Length = Screw Thread Length + Shaft Head Processing Length
左右旋滾珠絲桿如何確認“行程”-導軌絲杠:http://www.306135.com

How to confirm the "stroke" of the left and right ball screw - Guide screw: http://www.306135.com
接下來,就說說各個因素所代表的含義是什么吧?
Next, what does each factor mean?
A、絲桿螺紋長:整根絲桿全部的螺紋長度;
A. Thread length of screw: Thread length of the whole screw;
B、有效行程:螺母從絲桿的這端移動到另一端所經過的距離;
B. Effective stroke: the distance the nut travels from one end of the screw rod to the other end;
C、余量長度:
C. Length of allowance:
1 、螺母的長度
1. Nut Length
2 、絲桿兩端機加件干涉不能被螺母經過的長度
2. Length of the interference between the additives of the two ends of the screw that cannot be passed by the nut
3 、距離
3. Safe Distance
關于第3點補充說明,一般螺紋兩頭建議預留20mm左右的距離,1、此處有絲桿退熱處理余熱會導致溝槽有適量變形而不適合運行,2、20mm內處會適當加工扳手位不建議滾珠運行到此處,否則會產生磨損破裂。
As for the third point, it is generally recommended to reserve a safe distance of about 20 mm at both ends of the thread. 1. The residual heat of screw rod retreatment here will cause the groove to deform properly and not suitable for operation. The wrench position within 2 and 20 mm will be properly machined and the ball will not be recommended to run here, otherwise wear and tear will occur.
以上是導軌絲杠制造商為大家整理的相關內容,想要了解更多內容,歡迎訪問我們網站:http://www.306135.com
The above is the relevant content of guide screw manufacturer for you. For more information, please visit our website: http://www.306135.com.
相關新聞 /RELATED TO RECOMMEND
導軌絲杠選型必看!滾珠絲杠研磨級VS軋制級,選錯多花冤枉錢還影響精度
2026-05-04
導軌絲杠選型避坑!滾珠絲杠為何普遍不加減速機?附電機驅動選型案例
2026-05-03
滾珠絲桿裝配錯1步=精度報廢,導軌絲杠精密裝配全流程,零間隙實操指南
2026-04-27
導軌絲杠:精密傳動界的扛把子,聊聊滾珠絲桿的那些事
2026-04-24
導軌絲杠:滾珠絲杠副冷卻結構設計及溫升影響分析
2026-04-22
導軌絲杠選型避坑,梯形VS滾珠絲桿核心區別,90%從業者都選錯
2026-04-20
導軌絲杠裝配避坑!全流程實操詳解,80%的故障源于裝配不規范,一次達標不返工
2026-04-13
導軌絲杠 | 滾珠絲杠避坑指南!原理吃透不踩雷,高精度傳動99%的人都沒搞懂核心邏輯
2026-04-08
導軌絲杠選型避坑!四步法精準選型,90%工程師都在用,杜絕動力不足、共振隱患
2026-04-07
別再瞎選導軌絲杠!垂直安裝不設防墜,幾千斤負載直接砸穿設備
2026-04-06
滾動 vs 滑動:導軌絲杠選錯,磨損翻倍、維護成本直接飆升
2026-03-27
導軌絲杠:人形機器人直線運動核心,一步穩不穩全看它
2026-03-26
相關產品 /RELATED TO RECOMMEND




